June 13, 2014

Thin is In!

I guess some people are concerned about going ‘thin on the top”, but today’s post is about going thin on the bottom! So, in the case of a bra band, thin might be in!  Why would you want a thin band?

Does your band roll up or in?
Do you have a little “shelf” of flesh at your centre front, directly under your bra? Do you like the look of a partial band bra, but do not wish to wear wires? Do you want to use wider elastic on the bottom edge but cannot because it will curl? If you answered "yes" to any of these questions, you may want a thin band.

Check out this ready-to-wear bra (the once best selling WonderBra 1219) and you can see clearly, that the band is rolling inward. This bra is fresh out of the wash too, so it’s not because I was wearing it immediately before the picture was taken, that it has a tendency to roll. The band on this bra has a depth of 1/2” (12 mm) under the apex, and it definitely rolls. It’s not uncommon at all to see a narrow band depth of 1/2” (12 mm) rolling. So is this a fault of the bra manufacturers?


Maybe you are thinking the band curls because you made your own bra and maybe...somehow you missed an important step? 

No, it is not. 

Let me make this next part perfectly clear. Any elastic on the bottom band can curl, and the problem is worse if you have a high tummy right under the bust. The wider the elastic, the more the tendency to curl. If you are slender or long-waisted, you may never experience this. I wish I could say I haven't...but sadly, I lived with this every day. In fact, I thought this was "normal".

That is.......until  I noticed that some very high-end ready-to-wear bras had a very thin band in the area right under the cups. So thin that they appeared to be a partial band bra with no band running under the bust. The band was so thin that it looked like a partial band bra. 

What? You don't know the difference between a full band and a partial band?

Here's a comparison of partial vs. full band bras. Here's the full band bra. You can see there is about  1/2" - 5/8" (12-15 mm) of band all across under the cups and under the wire line.
But here is the partial band (or frameless bra) which is always an underwired bra. It's actually the wires that make this bra work. The back band stops  at the cup on the side. There is a separate piece (the bridge) that joins the two cups together. There is no band under the cup. What you see is the cup edge turned under and channeling sewn on to hold the wire. It really cannot curl up because the wire is holding it down.
Lots of women think they are wearing a partial band bra, but upon closer examination, we 
discover it is a full band after all.  Check your own bra closely, to see whether there really is a band at the bottom. A sure indication of a band is found by turning the bra over to show the inside. 

Does the elastic continue all the way across the bottom edge? It doesn't matter if the elastic is covered partially by the wire channeling, as long as you can see the elastic continuously across the bottom - it is a full band. Does the bra have underwires? If it does not, the bra has to be a full band; only full band (“frame”) bras can exist without wires. 

This bra below is a full band, and you can see the picot edge of the elastic is continuous across the bottom edge. This bra looks like a partial band but it is a full band bra.

I achieved the minimalist look of a partial band bra by “thinning” the band on a full band bra, thus keeping the framework of a full band bra intact. 

Now take a look at this bra that I made, from the inside. You can hardly see any elastic peeking out from under the channeling, in fact, all you can see are the elastic picots running under the cup. This band has been thinned to its absolute minimum width (the width of the channeling). So where does the elastic go? It certainly looks like it has disappeared. Hint ... it's hidden under the channeling


The elastic I used on the bottom of the band is 1/2” (12mm). The more astute among you, might already be questioning how can you hide 1/2” (12 mm) elastic behind 3/8" (10 mm) channeling. 

Ahhh…..watch and learn, my Fairy Bra Children!

On the pattern piece, measure down 3/8" (10 mm) or the width of the channeling if yours is different -  from the seamline of the cup, not the cutting line. Taper from this point under the bust over to the side seam. You may decide to shorten the bridge at the same time. You can see here the pink line is the new sewing line and I decided to raise the bridge a little too.




Add the elastic allowance to the new sewing line, which is equal to the width of the elastic you are using. In my case, that would be 1/2" (12 mm).  here is the new pattern piece showing the new thin area under the cup.

One wee problem...the elastic will now almost always be wider than the space allowed for it in this area. We only allowed 3/8" (10 mm) and the elastic is 1/2" (12 mm). 

That means the elastic for the bottom band will have to be trimmed a wee bit after the first step of its application in order to lay flat under the wire line seam. You can see the elastic trimmed only in the area where the elastic intrudes into the wire line seam. This area is right at the bottom of the cup. 
Trim away only enough elastic to clear the seamline and to allow the channeling to lay flat outside the cup. Do not worry about trimming the elastic! The channeling will roll over the cut edge and cover them completely (as long as you are careful about the trimming and don't get too scissor-happy!)

When stitching the elastic for the second time, you will have to direct your stitching downward to catch the cut edges. Don’t fuss about this. Strive for evenness in your stitching and the slightly narrower section won’t show.
Here is a different bra that has a thin band. Notice the skinny band under the cup and the topstitching of the wire looks like it stitches right over it. But it doesn't. This is Bra Magic!
It's been at least 10 years since I tried this band thinning for myself - now every single bra I make for myself has a thin band. No more curly edges for me!

7 comments:

  1. I'm wearing a bra that is doing that right now.... so annoying. So thankful for the explanation of the difference between the full band and no band. I love the bra making tips even though I haven't made one ... yet.

    ReplyDelete
  2. You know, I wasn't going to put in the difference between the two types of bras...then I figured...not everyone who reads this post is familiar with bra-making and all its terminology. So thanks Summer, for confirming that my reckoning was spot on!

    ReplyDelete
  3. Ok, but why not just make partial band bras??

    ReplyDelete
  4. Lots of women don't like partial band bras including me. They just don't sit the same way. Also if someone does not want wires, they have to use a full band

    ReplyDelete
  5. I love this post, Beverly! I refer to it so often. It's a great alteration and makes the bra so much more comfortable without sacrificing the support of the wider elastic and the full band. Thanks!

    Michelle

    ReplyDelete
  6. The rolling elastic drives me crazy so I will try the thinner band next bra but I ordered the large kits already Beverly...can I buy the 1/2" elastic in the 2 colors I just got from you?

    ReplyDelete
    Replies
    1. Yes, you can. We stock 12 colours of bra components, and they all match our duoplex and power nets very nicely!

      Delete